R.H. Peterson G8 series Owner's Manual download pdf (Page 24)

OUT

When shutting your burner down, be sure to TURN THE

FLAME FULLY OFF (to PILOT or OFF). Make sure the

burner is completely off for one minute before relighting.

ADJUSTING THE ODS PILOT

a. The ODS pilot ﬂ ame should encircle the generator

tip, and is preset at the factory (

Fig. 24-2).

Ordinarily, the ODS pilot will not require field

adjustment.

b. If adjustment is necessary, remove the cap screw

(

Fig. 24-1) and turn the smaller gas adjustment

screw inside

counterclockwise to increase the

ODS pilot ﬂ ame, and

clockwise to decrease

the ODS pilot ﬂ ame. Replace the cap screw.

MAINTENANCE

Your pan burner is equipped with a safety ODS pilot

that will shut off the gas supply in case the ODS pilot is

not burning or functioning properly. Make sure the ODS

pilot is adjusted properly and that the generator spade

clips are tightly connected to the terminal screws on

the valve. If the ODS pilot will not stay lit, call your local

gas utility or gas supplier.

A periodic check of the following should be performed

at least annually by a qualiﬁ ed professional service

representative:

1. Valves and switch for proper operation.

2. Flue system for rust, damage, or leaks.

3. Damper operation.

4. Oriﬁ ces for dirt or other foreign matter.

5. Visual check on the burner.

If this unit was shipped with a remote, or if a remote

system was installed later, read and follow the

separate remote instructions to operate the burner

remotely.

WARNING

If you do not follow these instructions exactly, a ﬁ re or explosion may result, causing property

damage, personal injury, or loss of life.

Do not use this appliance if any part has been underwater. Immediately call for a qualiﬁ ed professional service technician

to inspect the appliance and to replace any part of the control system and any gas control that has been underwater.

FOR YOUR SAFETY, READ BEFORE LIGHTING

LIGHTING THE ODS PILOT

To read the safety valve control knob (Fig. 24-1),

read the marking nearest the teardrop-shaped metal

pointer.

1. If the safety valve control knob is in the PILOT

position, push in slightly on the knob and rotate it

clockwise

to the OFF position.

2. Release knob and wait ﬁ ve minutes.

3. Turn safety valve knob counterclockwise to the

PILOT position. (Only the ODS pilot gas will ﬂ ow

when the knob is pushed in.)

4. Place a long match or a butane lighter at the ODS

pilot burner, and at the same time, push the safety

valve knob fully in. The ODS pilot will light.

5. Hold the safety valve knob in for approximately 60

seconds before releasing.

6. If the ODS pilot does not stay lit, turn the safety

valve knob clockwise

to the full OFF position.

Wait ﬁ ve minutes, then repeat steps 3 through 5.

IGNITING THE MAIN BURNER

With the ODS pilot lit, turn the safety valve knob

counterclockwise to the ON position. Flip the switch

control to the ON position and the burner will light.

Refer

to the PARTS LIST for the switch location.

SHUTTING OFF THE MAIN BURNER

Flip the switch control clockwise to the OFF position.

The ODS pilot will remain lit.

SHUTTING OFF THE ODS PILOT

Be sure the switch control is OFF and depress and turn

the safety valve knob

clockwise to the OFF position.

Fig. 24-1

Wiring harness

ODS pilot

cap screw

HI/LO ﬂ ame

height knob

Note: ODS pilot ﬂ ame should encircle top of the thermopile

Fig. 24-2 Lighting the ODS pilot

LIGHTING INSTRUCTIONS - SERIES 12 VALVE

The Real-Fyre

burner system has an ODS (Oxygen Depletion Sensor) pilot which can be lit by hand using a match or lighter.

When lighting the ODS pilot, follow these instructions exactly.

BEFORE LIGHTING, smell all around the burner area for gas. Be sure to smell next to the ﬂ oor as some gas is heavier than

air and will settle on the ﬂ oor. IF YOU SMELL GAS, FOLLOW THE INSTRUCTIONS ON P. 1.

Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't

try to repair it. Call a qualiﬁ ed professional service technician. Force or attempted repair may result in ﬁ re or explosion.

Flame touching

Thermocouple

ODS pilot

gas port

Safety

valve

control

knob

To remote

(if applicable)

Switch

The Real-Fyre

burner system has an ODS (Oxygen Depletion Sensor) pilot that can be lit by using the built in piezo ignitor switch

on the burner, or by hand using a match or long necked lighter. When lighting the ODS pilot, follow these instructions exactly.

4. Push and hold the safety valve knob fully in and

push in the piezo ignitor button several times until

the ODS pilot lights.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 30

Comments to this Manuals

No comments

R.H. Peterson G8 series Owner's Manual Page 24

Comments to this Manuals

Related products and manuals for Fireplaces R.H. Peterson G8 series